Your ultimate solution for tube cutting performance

 

Unlock the full potential of your tube cutting operations with the TUBE HT Pro saw blade.

With cutting speeds up to 330 m/min at very high feed rates, the PVD coated carbide tipped TUBE HT Pro is your optimal solution for high volume and high tensile tube applications.

It has specifically been designed for cutting all types of high tensile tubes with a high output and will perform at its best at tensile strengths between 1,000 – 1,500 N/mm² at a wide range of demanding tube applications and steel grades. Typical products are drive shafts, twist beams, camshafts, suspensions and differentials.

Achieve an almost flawless surface finish that meets the highest standards of your industry and minimize or avoid post-machining, therefore saving cycle time and tool costs.

* Only available in Austria, Czech Republic, Denmark, Finland, France, Germany, Italy, Poland, Slovakia, Sweden, Switzerland, United Kingdom and United States

Advantages:

• Suitable for all types of tubes
• Specifically designed for cutting high tensile tubes with a high output
• Higher blade life, especially when cutting higher tensile strength tubes
• Very high feed rates
• Because the cut surface is as close to the end stage as possible, you will minimize or avoid post-machining, save cycle time and tool costs.

 
Applications:

• Cutting high tensile tubes with high output (best performing between 1,000 – 1,500 N/mm²)
• Cutting speeds up to 330 m/min
• Tooth load: 0,035 – 0,20 mm/tooth
• When focussing on output, using high parameters is advised. Please note, this does come at the expense of blade life.
• When focussing on blade life, using regular parameters is advised.

 
TUBE HT Pro is ideally suited for cutting large volumes of high-tensile steel, as used primarily in the automotive industry.
 
Typical applications include:

• Seating components, headrests
• Sleeves, cylinders, bushings
• Drive shafts, side shafts, half shafts
• Twistbeam
• Chassis / body structures, stabilizer bars, instrumental panel beams
• Camshafts, piston rods
• Suspensions, shock absorber parts
• Steering mechanics
• Fittings, couplings
• Differentials

 
Typical steel grades:

• Carbon steel (E355 +C)
• High Carbon, high tensile
• ‘Sticky’ materials
• High Strength Low Alloy (HSLA)
• Advanced High Strength Steel (AHSS)
• Manganese (Mn) alloyed
• Boron (B) alloyed
• Docol (SSAB)
• Dual Phase (DP, ArcelorMittal)
• XPF grades (Tata)
• Specifically: 22MnB5 / 26MnB5 / 27MnB5 , 34CrMo4 / 34CrMo4-HC / 34CrMo4-LC / 34MnB5 , MW1000L / MW700L

 

Typical machines
Manufacturer	Machine type
Rattunde	ACS
RSA	Rasacut
Sinico	Top
Bewo	DCH / SCF (single/double)
Soco	SA series
Adige / BLM	TS/CM series

 

STANDARD RANGE TUBE HT Pro
Diameter (mm)	Kerf (mm)	Bore hole (mm)	Pinholes	No. of teeth (Z)
315	2,3/2,0	32	4/9/50 4/12/64	100
315	2,3/2,0	32	4/9/50 4/12/64	120
315	2,3/2,0	40	2/9/55 4/12/64	100
315	2,3/2,0	40	2/9/55 4/12/64	120
350	2,7/2,5	50	4/16/80	100
350	2,7/2,5	50	4/16/80	120
350	2,7/2,5	50	4/16/80	140